factured to ANSI/AWWA-C110/A21.10 standard. These fittings have identical face to face and center to face dimensions and the same flange drilling as ANSI B16.1 fittings, but differ slightly in wall thickness. Ductile iron C110/A21.10 flanged fittings are rated for 150 or 250 psi water working pressure as listed in the tables.

PDF ANSI/AWWA C110/A21 DRILLING: In accordance with ANSI/AWWA C110/A21.10, ANSI/AWWA C153/A21.53 and ANSI B16.1 Class 125 Flanges CEMENT LINING: In accordance with ANSI/AWWA C104/A21.4 -- sizes 1"- 3" single thickness and sizes 4"- 64" double thickness COATING: Asphaltic seal coat inside in accordance with ANSI/AWWA C104/A21.4 and

Available in the following compounds: Sizes 4" - 36", 1/8" Nominal Thickness Rated for a water working pressure of 350psi For 4"-24" and 250psi for 30"-36" and are based on maximum rating of C110, C111 & C153 flange Holes match ANSI A-21.10, A21.15 and B 16.1 Class 125 Flange drilling. Designed for unique surface of Ductile Iron Flange joints

Look Inside This standard covers 3- to 48-in. (76- to 1,219-mm) gray-iron and/or ductile-iron fittings to be used with ductile-iron pipe for water.

Standard 125 pound template for drilling shown below is used for all flanged fittings whether ANSI/AWWA-. C110/A21.10 or ANSI B16.1. Note: The flanges shown 

C110/A21.10, C153/A21.53, or AMERICAN Standard Flanged Fitting Dimensions and Designation of Outlets Dimensions for above fittings are given in Table No. 6–2. Some of the above fittings are not listed in AWWA C110 but

AWWA Ductile Iron C110 Full Body Bends FILTER BY 123 results for "AWWA Ductile Iron C110 Full Body Bends" Category: AWWA Ductile Iron C110 Full Body Bends Sort Show List View 2 in. Mechanical Joint Ductile Iron C110 Full Body 45 Degree Bend (Less Accessories) Part # FB4LAK Item # 1318187 Mfr. Part # 056348 To see availability for this product,

TESTING: • In accordance with ANSI / AWWA C110 / A21.10 where applicable. • Other items are in accordance with manufacturer’s standards. • 54” and above Flanged Fittings are manufactured as per AWWA C153/A21.53.

Awwa C110-12 Ductile-iron and Gray-iron Fittings (Paperback)

As one of the leading awwa c110 flange and flare manufacturers and suppliers in China, we warmly welcome you to buy bulk awwa c110 flange and flare made in 

ANSI/AWWA C110/A21.10, NFPA 13/24, 3” - 12” UL listed and approved (File - Tyler Union). MATERIAL: Cast of ASTM A536 qualified ductile iron.

C110 Mechanical Joint Fittings 700 Goldman Drive Cream Ridge, NJ 08514 800 999 2550 p 609 758 1163 f [email protected] SIGMA Corporation www.sigmaco.com C110 Mechanical Joint Fittings 3"-48" FULL BODY MECHANICAL JOINT FITTINGS BASIC SPECIFICATIONS MATERIAL: Ductile Iron ASTM A536

TESTING: • In accordance with ANSI / AWWA C110 / A21.10 where applicable. • Other items are in accordance with manufacturer’s standards. • 54” and above Flanged Fittings are

3. AWWA C401 The Selection of Asbestos Cement Distribution Pipe, 4 inch through 16 inch for Water and Other Liquids. 4. AWWA C402 Asbestos-Cement Transmission Pipe 18 inch through 42 inch for Potable Water and Other Liquids. 5. AWWA C403 The Selection of Asbestos-Cement Transmission and Feeder Main Pipe, 18 inch through 42 inch. 6.

AWWA C110/A21.10 January 27, Ductile-Iron and Gray-Iron Fittings This standard describes 3- to 48-in. (76- to 1,219-mm) gray-iron or ductile-iron fittings to be used with ductile-iron pipe for water, wastewater, and reclaimed water. Requirements for fittings with AWWA C110/A21.10 June 15, 2003 Ductile-Iron and Gray-Iron Fittings for Water

COATING: • Interior of fitting is seal coated (asphaltic material) in accordance with ANSI/AWWA C104/A21.4 and NSF61 approved. • Exterior of fitting is seal coated (asphaltic material) in accordance with ANSI/AWWA C110/A21.10 and NSF61 approved. GASKETS: • SBR in accordance with ANSI/AWWA C111/A21.11. • Also available in EPDM, NBR and CR.

strict accordance with AWWA C110, ANSI A21.10. Material: Ductile Iron, ASTM A536. Flange: Faced and drilled in accordance with ANSI B16.1 Class 125. Lining:.

AWWA C110, ANSI A21.10 UNITED BRAND FITTINGS. reducers, and blind fl anges. All are manufactured in strict accordance with AWWA C110, ANSI A21.10. Material: Ductile Cast Iron, ASTM A536, Grey Cast Iron, ASTM A-126 Flange: Faced and drilled in accordance with ANSI B16.1 Class 125 Lining: The standard lining is cement mortar with bitumen overlay

Shop for AWWA Ductile Iron C110 Full Body Tees at Ferguson. Ferguson is the #1 US plum supply company and a top distributor of HVAC parts, waterworks supplies, and MRO products.

C110-21 Ductile-Iron and Gray-Iron Fittings C111-17 Rubber-Gasket Joints for Ductile-Iron Pressure Pipe and Fittings C115-20 Flanged Ductile-Iron Pipe with Ductile-Iron or Gray-Iron

ANSI/AWWA C110/A21.10-12 (Revision of ANSI/AWWA C110/A21.10-08) AWWA Standard Effective date: May 1, 2012. First edition approved by AWWA Board of Directors May 4, 1951. This edition approved Jan. 22, 2012. Approved by American National Standards Institute Feb. 23, 2012. 6666 West Quincy Avenue Advocacy Denver, CO 80235-3098 Communications

Buy Awwa C110 China Direct From Awwa C110 Factories at Alibaba.com. Help Global Buyers Source China Easily.

Flanged Fittings - AWWA C110 Class 250, ANSI B16.1 Class 125. Flanged Fittings. Our dedication to the mechanical piping industry has 

10/21 · AWWA C110-98 January 1998 American National Standard for Ductile-Iron and Gray-Iron Fittings, 3 in. through 48 in. (75 mm through 1200 mm), for Water and Other Liquids

AWWA Headquarters 6666 W. Quincy Ave. Denver, CO 80235 USA Phone: 303.794.7711 or 800.926.7337 AWWA Government Affairs Office 1300 Eye St. NW Suite 701 Washington, DC 20005 USA Phone: 202.628.8303 AWWAIndia Association New Delhi, India https://www.awwa-india.org

2”-16” Underwriters Laboratories listed and Factory Mutual Approved. STANDARDS: ANSI / AWWA C110 / A21.10 Where applicable. Other items are in accordance with