USG Shaft Wall Systems are non-load-bearing gypsum wall partition assemblies constructed from outside the shaft at each floor. Shafts are enclosed early in construction, and the walls are finished later, along with interior partitions. Installation is quick and easy, using components and application procedures familiar to drywall contractors.

The clips are used to hold the area separation wall assembly in place at the floor, roof and truss line between adjacent units. Should a fire break out in one unit, the Aluminum Burn Clips on the fire-ridden side of the area-separation wall will melt, allowing the wall structure for that side to collapse.

Three-Hour Cavity Stair Wall (Non-Load Bearing), See Figure 5 4. 1-in thick SHEETROCK® Brand Gypsum Liner Panel - Friction-fitted in "H" portion of C-H studs. Two-Hour Horizontal Stud Shaft Wall Assembly (Non-Load Bearing), See Figure 6 1. A minimum 4-in deep 20 gauge J-runner to be installed vertically, on the ends of the wall.

USG Middle East’s ever-growing portfolio of groundbreaking ceilings systems, drywall assemblies, and end-to-end solutions is backed by unparalleled quality service. With an extensive distribution and sales network operating for more than 25 years across the MENA Region, our dedicated teams provide local expertise and high levels of support in finding the right solutions for your

USG CH Shaftwall Stud 34 mil "CH" studs are fabricated in web depths of 2-1/2″, 4″, and 6″ each with a short-flange width of 1-3/8″ and long-flange width of 1-1/2″. All C-H studs manufactured by CEMCO are produced from hot-dipped galvanized steel in standard G40 coating. G60 is available upon special request.

WALL ASSEMBLY GUIDE NFPA 285 Per Chapter 26 of the International Building Code, the wall assembly shall be tested in accordance with and comply with the acceptance The window opening perimeters shall be per UL Design Listings EWS0013, EWS0029, or EWS0054, as applicable. Title: CSFI-12630 NFPA 285 Exterior and Cavity Wall Assembly Guide.

OF SUCH MODIFICATIONS, MODIFICATION OF USG PRODUCT CAD DRAWINGS IS THE SOLE RESPONSIBILITY OF THE DESIGN PROFESSIONAL. 0 10/16/ 1 OF 1 01 HEAD OF WALL PARTITION DETAILS FIRE RESISTANT ASSEMBLIES HEAD

Title: USG Fire Resistant Assemblies Wall Penetration Details (English) - J2133 Keywords; null Created Date: 10/16/ 6:36:15 AM

A 2-hour fire-resistive, non-load bearing non-combustible partition designed to enclose shaftwalls, containing elevators, ducts, piping, air shafts and similar construction applications. System consists of 1" shaftliner panels supported by 2-1/2", 4" or 6" C-T studs and faced on one side with two layers of 1/2" Type C or 5/8" Type X gypsum board.

USG provides resources here for our UL wall assemblies for seamless integration into any construction project. These wall assembly files are used for 

CEMSCO products are manufactured to the standards established by the American Iron and Steel Institute. Veiw our resources on Typical Details-USG Shaftwall Assemblies here! Find a Distributor CEMCO distributes our products throughout the Western United

4 USG Shaft Wall Systems Overview USG shaft wall systems are non-loadbearing gypsum wall partition assemblies constructed from outside the shaft at each floor. Shafts are enclosed early in construction, and the walls are finished later, along with interior

CGC Shaft Wall Systems are non-load-bearing gypsum wall partition assemblies constructed from outside the shaft at each floor. Shafts are enclosed early in construction, and the walls are finished later, along with interior partitions. Installation is quick and easy, using components and application procedures familiar to drywall contractors.

Our Shaftwall Metal Framing can be installed for vertical and horizontal encasement applications. With the help of a variety of mold, moisture, and fire-resistant gypsum and cement boards that USG Middle East offers, the result will be thinner and lighter walls that can withstand high lateral loads and improve acoustic performance. 4 Items

Shaftwall. One layer 1″ x 24″ (25.4 mm) ToughRock® Shaftliner or DensGlass® Shaftliner panel inserted between 2-1/2″ floor and ceiling runners of 2-1/2″ steel C-T, C-H studs. Opposite side: Base layer of 5/8″ (15.9 mm) ToughRock® Fireguard X® Products or 2/8″ (15.9 mm) DensArmor Plus® Fireguard® gypsum panels installed

ASSEMBLY USG Shaft Wall Systems | 4 APPLICATIONS Use USG Shaft Wall Systems to construct elevator shafts, mechanical shaf ts, stairwells, air return shafts and horizontal membranes.

wall framing to accommodate the 1" (25.4 mm) DensGlass® Shaftliner panels used as fireblocking between the floor levels. The UL Design U373 and U375 Area Separation Wall assemblies were evaluated at a height up to 44' (13,411 mm) and the ITS/WHI GP/WA 120-04 Area Separation Wall assemblies were evaluated at a height up to 68' (20,726 mm).

11/1 · How can I achieve a higher STC shaft assembly? Insulate the wall, use resilient channels or sound isolation clips, and/or install Gold Bond® BRAND SoundBreak® XP® as one of the face layers. Here are a few UL 2-hour rated designs that achieve an STC of 50 or higher: U497, STC 52 (Sound Test: NGC2017007), U498, STC 53 (Sound Test: NGC2015036).

4 USG Shaft Wall Systems Overview USG shaft wall systems are non-loadbearing gypsum wall partition assemblies constructed from outside the shaft at each floor. Shafts are enclosed early in construction, and the walls are finished later, along with interior partitions. Installation is quick and easy, using components

USG Cavity Shaft Wall can be used in elevator and mechanical shafts, air ducts, stairwells, and areas where wall construction is only available from one side.

Fire-Rated Assemblies 3 USG Shaft Wall Systems 09 20 00/USG BuyLine 2425 1 Hour Fire-rated Construction Non-loadbearing Acoustical Performance Construction Detail Description Test Number STC Test Number wt. 8 † 5/8 SHEETROCK® brand FIRECODE® Core gypsum UL

45 USG-040903 Based on 4 C-H studs 25 gauge 51 RAL-OT04-018 Based on 4 C-H studs with 3 mineral fi ber insulation The assemblies listed below are a small sample of the UL Designs in which USG shaft wall systems can be used. For more details on fi re-rated assemblies, see USG literature SA926, Shaft Wall Systems.

USG Shaft Walls, Stair Walls & Corridors. Assemblies Evaluated For. 1. Non Axial Load Bearing Wall. 2. Transverse Load Capacity. 3. Fire Resistance.

4 OVERVIEW USG Shaft Wall Systems are non-load-bearing gypsum wall partition assemblies constructed from outside the shaft at each floor.

Wall Assemblies USG provides resources here for our UL wall assemblies for seamless integration into any construction project. These wall assembly files are used for planning and

USG Middle East يو إس جي للشرق الأوسط